PAICAR 03 Fine Cut
Regular price
$23.99
Formulated for the effective removal of light swirl marks, micro-scratches and residual holograms from previous compound steps, this fine polish is also ideal for eliminating sanding marks between P3000 and P4000, preparing the surface for the protection stage.
Its refined action restores color depth and enhances the natural gloss of the paintwork, giving the surface a uniform appearance free from visual imperfections.
Easy to work with thanks to its water-based, dust-free and residue-free formula, it guarantees a clean and smooth polishing experience, minimizing the need for intermediate cleaning. Removal is quick and effortless, allowing the operator to move easily to the next step without leaving streaks or oily residue.
Completely free from silicones and fillers, it delivers a true and transparent result, ideal for accurate inspection and for ensuring optimal adhesion of sealants or coatings.
USAGE
1. Surface preparation
Make sure the surface is clean and properly decontaminated (thorough wash, clay bar if necessary).
Completely dry the panel before starting the polishing process.
2. Pad choice
Use a soft or medium foam pad, ideal for the finishing stage.
With a dual action polisher for greater control and a deeper finish.
3. Product application
Shake the bottle well before use.
Apply 3–4 drops of product onto the pad.
Spread PAICAR 03 over the panel with the machine turned off, lightly dabbing it on.
4. Work process
Start spreading PAICAR 03 at the lowest speed.
Gradually increase the speed up to 4500 rpm.
Work in areas of approximately 40×60 cm (roughly the size of 6 pads), using cross-hatch passes (horizontal and vertical).
Apply light, consistent pressure, keeping the pad flat on the surface.
.5. Result inspection
After 3–4 passes, stop the polishing cycle (approximately 2 minutes).
Remove the residue with a clean, soft microfiber towel.
Inspect the panel with an inspection light to verify the removal of holograms and micro-scratches.
6. Finishing
Once the desired finish is achieved, apply a sealant, wax or coating to protect and…
enhance the result.
Pro tips
The polish contains no silicones or fillers, so the visual result is real and not masked.
Also ideal for pre-coating inspections where a perfectly clean surface is crucial, after a panel prep step.
Always work in well-lit, dust-free environments for an impeccable finish.
Cut: 6/10
Finish: 9/10
Color: white
Odor: light and pleasant
Physical state: creamy
Storage: 5–30°C
Shipping will be calculated at checkout.
Shipping will be calculated at checkout.
PAICAR 03 Fine Cut
Regular price
$23.99
Formulated for the effective removal of light swirl marks, micro-scratches and residual holograms from previous compound steps, this fine polish is also ideal for eliminating sanding marks between P3000 and P4000, preparing the surface for the protection stage.
Its refined action restores color depth and enhances the natural gloss of the paintwork, giving the surface a uniform appearance free from visual imperfections.
Easy to work with thanks to its water-based, dust-free and residue-free formula, it guarantees a clean and smooth polishing experience, minimizing the need for intermediate cleaning. Removal is quick and effortless, allowing the operator to move easily to the next step without leaving streaks or oily residue.
Completely free from silicones and fillers, it delivers a true and transparent result, ideal for accurate inspection and for ensuring optimal adhesion of sealants or coatings.
USAGE
1. Surface preparation
Make sure the surface is clean and properly decontaminated (thorough wash, clay bar if necessary).
Completely dry the panel before starting the polishing process.
2. Pad choice
Use a soft or medium foam pad, ideal for the finishing stage.
With a dual action polisher for greater control and a deeper finish.
3. Product application
Shake the bottle well before use.
Apply 3–4 drops of product onto the pad.
Spread PAICAR 03 over the panel with the machine turned off, lightly dabbing it on.
4. Work process
Start spreading PAICAR 03 at the lowest speed.
Gradually increase the speed up to 4500 rpm.
Work in areas of approximately 40×60 cm (roughly the size of 6 pads), using cross-hatch passes (horizontal and vertical).
Apply light, consistent pressure, keeping the pad flat on the surface.
.5. Result inspection
After 3–4 passes, stop the polishing cycle (approximately 2 minutes).
Remove the residue with a clean, soft microfiber towel.
Inspect the panel with an inspection light to verify the removal of holograms and micro-scratches.
6. Finishing
Once the desired finish is achieved, apply a sealant, wax or coating to protect and…
enhance the result.
Pro tips
The polish contains no silicones or fillers, so the visual result is real and not masked.
Also ideal for pre-coating inspections where a perfectly clean surface is crucial, after a panel prep step.
Always work in well-lit, dust-free environments for an impeccable finish.
Cut: 6/10
Finish: 9/10
Color: white
Odor: light and pleasant
Physical state: creamy
Storage: 5–30°C
Shipping will be calculated at checkout.
Shipping will be calculated at checkout.